Call Point Plus (952)
Nursecall Intercall 952 Call Point Plus
The Call Point Plus has all the functionality of our Call Point Standard, with the addition of a full duplex VoIP speech device providing the instant reassurance of human interaction. Our most advanced call system it can be deployed in assisted living programmes where residents are more independent.
Description
Description
Nursecall Intercall 952 Call Point Plus
The Call Point Plus has all the functionality of our Call Point Standard, with the addition of a full duplex VoIP speech device providing the instant reassurance of human interaction. Our most advanced call system it can be deployed in assisted living programmes where residents are more independent.
Related products
NC805C/6
1.8m (6ft) Tail Call Lead
A short 1.8m tail call lead for use with C-TEC’s Quantec and 800 Series Call Systems.
Allows users to remotely generate Standard calls from armchairs, beds, etc.
Comprises a pear-shaped call push, 1.8m (6ft) trailing lead and a 6.35mm remote jack plug.
Connects to the 6.35mm remote socket on compatible Quantec and 800 Series call points. If connecting to a Quantec-Pro call point, a QP805G1A (6.5mm to RJ12) adaptor is also required,
Activating the pear push or removing the tail call lead from a call point’s remote socket will generate a Standard call.
NC944
Four Zone Call Controller (requires NC930 12V 250mA PSU)
An attractively-designed four zone call controller c/w mute and reset buttons.
Fully compatible with C-TEC's entire range of 800 Series Call System components.
Capable of indicating standard (constant tone) and emergency (intermittent tone) calls.
Requires a separate NC930 12V 250mA PSU.
Includes four zonal alarm LEDs, RESET and MUTE buttons.
Two open collector outputs (Emergency and Aux Out).
Up to two NC944s can be connected to one NC930 PSU to create a mini-call system of up to 8 zones.
Mounts on a standard 25mm UK double gang back box.
QT-601-2
Quantec Controller
Supplies power to and controls a Quantec Addressable Call System.
Monitors all network devices and manages the routing and distribution of all calls.
Provides connections for network wiring, standby batteries, a laptop (for system programming), optional paging/DECT equipment, an optional printer or PC (to run Quantec’s QT707S Surveyor data management software).
Includes a library of 40 pre-set & 45 custom place names.
System setup requires a laptop PC running Quantec’s QT707 programming tools.
Can be semi-flush mounted using an QT385 bezel or fully-flushed using a BF359/3S stainless steel enclosure.
System wiring requires one or more QT603 network splitters.
Wiring should be made in a spine and limb arrangement using 1.5 to 2.5mm2 T&E (spines) and 4 to 8 core stranded security cable (limbs)
QT-603
Quantec Network Splitter
An essential wiring/installation aid for C-TEC’s Quantec Addressable Call System.
Helps protect against open and short circuit faults and reduces the risk of volt drop.
Includes one input and one output connection for Quantec’s ‘Spine’ wiring (typically 1.5-2.5mm T&E) and six fused 400mA ‘limb’ connections for the wiring of individual circuits containing Quantec’s field devices (typically 4 core stranded security cable).
At least one QT603 is required per Quantec system (the more you use, the easier it will be to program and fault-find).
Install one QT603 per corridor junction (locate at the end of the corridor nearest to the Quantec Controller). If the corridor is longer than 50m, install the splitter in the centre of the corridor to reduce wiring runs.
Mounts on a standard 25mm UK double gang back box.
‘Power’ and ‘Fault’ indicators.
Max. 60 addressable devices per QT603.
QT607
Ceiling/Wall Pull Unit
Can be used to generate a Standard or Ensuite call on a Quantec Addressable Call System.
Ceiling or wall mountable.
Typically wired to a Quantec Addressable Call Point or Quantec Accessible Toilet Reset Point.
Supplied with 3m of red nylon pull cord and two red open-sided triangular bangles for ease of use by the infirm.
Red confidence LED and diffuser emits a bright red glow over a wide area to reassure the user that a call has been made.
Surface mountable
Touch Display 948
The Touch Display is the central hub of the Touch series
nurse call system and the primary staff interaction point.
It helps nursing staff with monitoring while notifying them
of calls and alerts on the system, allowing them to decide
the most appropriate response. Multiple displays can be
installed, ideally on a desk or wall mounted, depending
on the size and individual needs of the care facility